EPiC – PolyCryl Two Pack
High Strength Enamel Surface Coating
EPiC PolyCryl is a High Strength Two Pack Floor Coating which provides excellent protection for Concrete, Timber, Masonry and Primed Metal surfaces with proven durability and performance. The coating provides excellent hardness and scuff resistance, designed for a wide variety of applications including commercial and industrial floors and walls.
Typical Uses
EPiC PolyCryl provides excellent protection against:
- Petrol
- Oil
- Fatty Oils
- Alkali
- Acids and Efflorescence
It has a high resistance to Corrosion and Abrasion and is impervious to Water and Moisture. PolyCryl is an Isocyanate free coating and is safer for use compared to Polyurethanes that contain Isocyanate. It is also suitable for use as a sacrificial Anti-Graffiti coating on concrete, masonry and metal surfaces.
Applications & Features
EPiC PolyCryl is used for a wide variety of applications where traditional floor paints, paving paint, epoxy coatings and furniture finishes are used. It has excellent interior and exterior durability, with high resistance to solvents, corrosion and abrasion after full curing is achieved. PolyCryl is highly petrol resistant and suitable for petrol stations and vehicle repair workshops. Designed as a 2 coat system, PolyCryl provides excellent protection against fading, powdering of oxide colours, staining or marking due to contaminants, oil or grease.
Equipment & Tools
Brush, Roller or Spray
Equipment Type
Good quality Brush and Roller Sleeve.
Spray application will depend on the type of finish required.
DO NOT store mixed product in spray equipment to avoid damage.
Surface Preparation
All surfaces must be free from Rust, Oil, Grease, and all other surface contamination. New concrete must have a pH level less than 10 and had at least 28 days to cure. New and old Concrete should be Acid Etched using 1 Part Hydrochloric Acid or Nu EcoSafe Concrete Etch to 10 Parts Water. High Pressure Water Blast area (> 2000Psi) and allow to completely dry. Painted concrete in poor condition should be stripped using our Nu Ecosafe range of paint strippers and acid etched before application.
Paint Mixture
Mixing Ratio
3 Parts A to 1 Part B.
After drill mixing leave to stand for 10 minutes before using to allow full activation. Stirring with a stick by hand is inadequate.
Pot Life
8 Hours
DO NOT use after pot life has expired.
Thinning
Brush, Roller
Nil
Spray
10% – 15% EPiC PolyCryl Thinners
Bare concrete and masonry surfaces should be thinned 20% – 25% for the first application coat to enable penetration and adhesion.
Dilute with EPiC PolyCryl Thinners.
Number of Coats
Brush, Roller
2 Coats
Spray
2-3 coats or a minimum of 130 microns wet film thickness
Dry and Re-Coat Times
Touch Dry
40mins @ 25° C
Re-Coat
After 2-4 hours but within 12 hours. If recoating after 7 days, the surface must be abraded.
Hard Cure
7 days
Clean Up
EPiC PolyCryl Thinners, PR Solvent or Gun Wash.
Coverage
8 – 10 m2 per litre, depending on concrete/porous surfaces
Other Information
Surface Temperatures
Above 10°C and below 30°C
Safety Precautions
- Wear suitable protective clothing, gloves and a recommended respirator for spray application.
- Make sure there is good air flow and ventilation before applying this coating.
Refer to Material Safety Data Sheet for additional safety and user information.
Slip Hazard
Sealing of smooth and sloping concrete surfaces will reduce pedestrian and vehicle safety. For greater slip reduction a Coarse or Fine 2PK Anti Slip can be sprinkled on the wet freshly applied surface of the first coat and encapsulated with a subsequent coat of EPiC PolyCryl. Testing is recommended before proceeding to ensure that a potential slip hazard is avoided. Refer to your Nutech specialist for alternative recommendations on steep, smooth surfaces.
Important Note
The information given in this data sheet is based on many years experience and is correct to the best of our knowledge. However as the use of our product is beyond our control we can only be responsible for the quality of our product at the time of dispatch. For additional information about specifications or application please contact our company. As this information is of a general nature we cannot assume responsibility for individual use.