DETAILED INFORMATION
Liquid Surface Creations™ &
Liquid Floor Art™

This fabulous new decorating product was recently featured on the ABC New Inventors Show. It has the DIY community buzzing about its modern snazzy appearance, ease of application and the low price. Liquid Surface Creations™ provides a 3 dimensional liquid glass appearance to almost any surface. Home renovators and new builders love it because you can make something unique by adding your own creative design effects on floors, kitchen splashbacks, shower and bathroom walls and floors and a wide range of other surfaces.

Liquid Floor Art™ was first developed for the Nutech Paint display stand at the 2004 Melbourne HIA Home Ideas Show . Although the product was not for sale at that time it attracted significant interest and undoubtedly resulted in our “Best Stand Award”.

The concept for the product came from the growing demand for polished and coloured concrete floors in shops restaurants, hotels and other commercial floors. The Liquid Floor Art™ range incorporates existing and newly developed polymer technology and offers a wide range of colours and textures which are easy to apply and low odour. The range includes user friendly water based and non-solvent based polymer floor coatings.

Liquid Floor Art™ is very economical compared to conventional tile and carpet solutions. It is also a low allergy floor coating which prevents mould, bacteria, dust mites and moisture to assist asthma and allergy sufferers. It is heat, moisture and sunlight resistant. Market research ha indicated that with increasing home and mortgage costs, low cost flooring products are highly sought after by 1 st home owners, architects, builders and renovators. Low cost, attractive and durable flooring solutions are also attractive for showrooms, shops, restaurants and other commercial buildings.

Initially our idea for the Liquid Floor Art™ was intended for domestic and commercial floors. We have been very pleased by the unexpected domestic and trade interest generated by the product and subsequently received hundreds of trade and export enquiries for the following innovative coating requirements;

• kitchen splash backs and benches tops,
• shower walls & bases,
• timber and steel stairs treads,
• table tops, sideboards & coffee tables,
• bar & restaurant table tops & joinery,
• domestic and commercial floors
• cupboard doors, front house doors,
• internal commercial doors and wall paneling,
• picture frames, air brush artwork back panels,
• fish tank surrounds & display walls,
• small and large corporate artwork wall features,
• commercial ceiling panels,
• transportable exhibition floor panels, exhibition display joinery,
• bed head and side rails, tops and inserts
• furniture,
• shop fittings and commercial displays
• light box panel faces applied semi transparent on glass or Perspex,
• architectural columns on PVC & cement sheet

After looking at the wide range of potential markets we decided to seek Patent protection for the chemical composition and application technique for this new product and broaden the potential for the product by registering the name Liquid Surface Creations™. Accordingly Liquid Floor Art™ and Liquid Surface Creations™ is the same product for different applications.

In early April 2005 we were granted Provisional World-Wide Patent Protection for Liquid Surface Creations™ in approximately 100 Countries covered by the International Patent Convention. The countries included importantly cover the USA, UK, EU, Australia and parts of Asia. Separate Patent protection is being sought for some individual countries outside this Convention.

One of the biggest potential markets for this new product is a kitchen splashback alternative and we are involved in discussions with a number kitchen manufacturers and major building product suppliers.

Eventually the product will be supplied pre-fabricated on coated compressed cement board of various sizes i.e. 900mm x 1200mm, 900mm x 2400mm and 900mm x 3000mm. It can also be applied on a special manufactured low density polyethylene sheet. This sheet is available 0.9m high up to 20 metres long in one piece for commercial applications. It can also be welded together to make very large panels if required for shop fittings or solid floors over cracked concrete, tiles or wooden floors.

The pre-fabricated cement sheets are easy to cut and trim with a simple diamond blade on a hand held angle grinder, electric or with a fine hand saw. Simply mark with a pencil and then cut. Edges do not chip or delaminate during cutting leaving clean smooth lines for neat detail work.

DIY customers will be able to purchase the sheet at building supply outlets such as Bunnings, take the sheet home and trim it to size, use liquid nails to glue it in place over any existing or new surface and silicon joints or use a coloured polyurethane sealant for a neat finish. This whole process should take no more than several hours to obtain "a perfect finish".

Alternatively customers may wish to purchase and pre-trim cement sheet to the correct size and then coat the board themselves to create a unique and stylish design.

The products benefits are;

• Very economical compared to glass and stainless steel.
• Similar cost to cheap tiles including installation with a snazzy modern and unique appearance and faster installation.
• Can be installed over old tiles, plaster or timber panelling (splash backs only)
• Easy and quick to install – DIY
• Kitchen cabinet manufacturers can easily cut and install this product at the same time as cabinetry is installed - no delays or added 3rd party costs
• Heat and fire resistant so suitable behind hot plates and next to deep fryers, BBQ’s and ovens (refer to Section below - Kitchen Spashback Fire Safety)
• Chemical resistant
• Can be repaired
• Scuff resistant (similar to typical polyurethane finishes on timber floors and benches)
• Can be sanded and recoated with a clear 100% solids finish to restore the gloss finish like new.
• Can be cut, drilled and shaped easily with no risk of cracking. Very sharp fine edges are prone to cracking if handled roughly during installation or cutting.
• Power points and other installations requiring holes or drilling can easily be installed by respective trades or the home owner.

Liquid Surface Creations™ can also be applied in a thin semi-transparent layer on Perspex or glass to create an interesting visual effect using back lights as an example. Some testing has been successfully completed with freshly cured product applied on thin board and Perspex which is then curved to form corners and interesting circular structures.

Liquid Floor Art™ can be applied directly on to the following floors;

• clean prepared concrete - a water based low odour epoxy primer may be required,
• stable ceramic, concrete or terra cotta tiles - light surface grinding required,
• steel sheeting - degreased and cleaned suitably
• weld jointed high density polyethylene or polypropylene sheeting.

This product is not suitable for cracked tiles with live moving cracks and timber floors including boards and chipboard which have joints because the product will eventually crack along movement joints.

Liquid Surface Creations™ is suitable for furniture, shop fittings, signs or other structures provided joints have been screwed and glued rigidly. The structures can be constructed from timber, craftwood, plywood, cement sheet, steel, plastic, concrete, terra cotta or other similar building material.

Any joint movement may eventually result in the appearance of cracks, although the durability and knock resistance is substantially better than conventional thin polyurethane or similar paint finishes.

Liquid Surface Creations™ is 100% waterproof and can even be used on surfaces under water such as concrete ponds, statues, swimming pools, fountains and other water features.

Future Markets and Overseas Agencies

Liquid Surface Creations™ was developed entirely by Nutech R&D and is a unique and novel use of polymer resin technology. No similar product is available to our knowledge and a World-wide patent search has not revealed any similar product on the market or in development. We believe the marketing potential for this product is greater than any product manufactured by our Company to date. For this reason we have taken considerable legal steps to protect the intellectual property.

The potential for this product in a wide range of markets is enormous. We are seeking partnerships and expressions of interest for overseas agencies and distributors.

Application Rates

Liquid Surface Creations™ is applied at a rate of 1 to 1.5 litres per 1 square metre of surface using a trowel application technique. The White/Green Glass colour requires approximately 2 square metres per litre due to the low opacity and glass like appearance of this colour.

Smoother finishes and dark colours will require approximately 1 litre per 1 square metre resulting in a coating thickness of 1.0 mm. High build textures and lighter colours require 1.5 litres per square metre resulting in a coating thickness between 0.75 to 1.0 mm.

Using a roller or brush interesting textures can be obtained with more economical application rates up to 0.5 litres per 1 square metre.

It is important to note that on commercial and high wear surfaces such as floors and kitchen benches a top coat of water based Nutech Aqua Polyurethane is recommended to reduce scuffing and scratching. Low wear surfaces such as decorative wall panels and splashbacks do not require this protective coating. The Aqua Polyurethane is applied in one or two coats at the rate of 1 litre per 10-12 square metres per coat.

Refer to the next section regarding primer requirements. Nutech Accopol 847 and PaveCoat are applied at approximately 6-8 square metres per litre in one coat. Nutech Aqua Epoxy is applied at 1 litre per 10-12 square metres.

Surface Preparation and Primer Requirements

On clean new compressed cement sheet priming is not a pre-requisite unless a light colour is being used or a dark colour base is required for special effect. The Snow White and White/Green Glass colours require a white primer coat. For kitchen splash backs next to gas hot plates Nutech White Aqua Epoxy is recommended because it is heat resistant. For non heat areas Nutech Accopol 847 or PaveCoat are recommended. For light coloured LSC a white primer coat is recommended.

If using on compressed cement sheeting which will be used for shower walls or bases, sealing all sides of the board and edges is highly recommended to protect the compressed sheet and substrate if joints or edge seals leak eventually.

To improve surface adhesion on porous surfaces or seal wet areas and provide a base for light colours, we recommend one coat of Nutech Aqua Epoxy applied at 1 litre per 10-12 square metre or Nutech Accopol 847 or PaveCoat applied at 1 litre per 8-10 square metres. Allow 12-24 hours curing before applying Liquid Surface. Do not exceed 24 hours before overcoating.

On non porous surfaces light sanding or grinding is recommended to provide a surface key. On these surfaces a primer is not required unless a light colour is being used. It is very important to ensure that the surface to be coated is clean and free of contamination from grease, oil, food, dirt, silicon, chewing gum, confectionary, flaking paint, varnish or other old coatings before applying Liquid Surface Products.

Experimenting with dark coloured primers for blue, green, gold, red and other top coat colours has provided very different and interesting finish effects.

Refer to Nutech surface preparation Guidelines for full details before application. Nutech accepts no responsibility if inadequate surface preparation results in adhesion problems. Testing for adhesion on unspecified surfaces is recommended before commercial use.

Adhesion on smooth glass surfaces is improved with the addition of a suitable glass adhesion promoter or primer.

Liquid Surface Creations™ is not recommended for concrete surfaces where hydrostatic water pressure is a problem from beneath the concrete, e.g. wet sub-basement floors and on floors above steam or cooking equipment in commercial buildings. Osmotic blistering can result if inadequate surface adhesion is established and hydrostatic moisture is present. Testing moisture content in concrete floors is recommended before commercial application of Liquid Floor Art™ products. Moisture levels should be below 5%.

New concrete floors, concrete repairs and cementitious patching and self leveling compounds must be allowed to cure for a minimum of 28 days under normal weather conditions before applying Liquid Floor products. Where surface filling and leveling is required Nutech Epoxy Patching compounds are recommended which can be overcoated within 24 hours.

To create longer cement sheets a piece can be added to the end of a panel before coating using fibre reinforced fiberglass or with fibre reinforced Liquid Surface Creations™.

Mixing, Curing & Application

Liquid Surface Creations™ is supplied as a 2 parts mix;

Part A Colour - 5 parts by volume

Part B Hardener - 4 parts by volume

The mixing ratio is very important and we recommend that all the Part A is added to the Part B as supplied and then stirred thoroughly. Adding extra hardener will not improve the product and can cause problems for the finished appearance. Part A with Part B must be mixed with a high speed drill for approximately 5 minutes. The product is then rested for several minutes and the drilled again for an additional 2 minutes. Mixing with a stick or slow drill will not adequately combine the two components and problems such as a loss of adhesion, appearance, gloss or other detrimental results can occur.

After mixing the product will be useable for about 30 minutes, subject to ambient temperatures. At 30 degrees Celsius the product will react faster and the pot life will be reduced.

After application at 20 Degrees C. the product will take approximately 2-4 hours to initially harden and 24 hours before it can be touched and moved. After 48 hours the product can be carefully cut & trimmed however it will still be ‘green’ and can be scuffed, scratched and damaged if care is not taken to protect the new surface. The product will take an additional 10 days to reach full cure and ultimate hardness.

If the mixed Part A & Part B is left in the can for too long a thermal reaction will occur and the container and contents will become very hot. Once this reaction begins the coating is no longer usable. There is no risk of fire, however caution should be taken handling the hot container.

If a coated panel or part is placed in an oven or heat chamber for 1 hour after application at 50-60 Degrees C. the coating will be touch dry after several hours and full curing will be reduced to 24 hours.

Heating a room with central heating or external heaters will rapidly reduce the curing time.

Application Techniques & Information

It is important that the room where the product is applied has an ambient temperature of more than 18 Degrees C. Application and curing below this temperature may result in blushing and unattractive surface defects. Do not apply in direct sunlight. The ambient temperature should be maintained below 30 Degrees C. in the first hour after application to enable adequate time for application tool defects such as bubbles to release and self level.

The recommended application and finishing tool is a 180mm (7 inch) Steel Gauging Trowel. For large panels and floors it is easier to spread the product quickly and evenly using a 100mm x 335mm or similar Round end Steel Trowel. For fine pattern finishes a smaller pointed or rounded trowel is useful.

It is also possible to finish the coating with a smooth or textured roller. Using a patterned or leather grained roller provides a very even stipple finish. A very interesting stippled effect can be obtained using this technique. Dragging a brush or broom over the spread coating can also provide an interesting grained effect. Spray application is also possible which is a very economical technique, although a more solid colour finish is obtained and specialised equipment is required.

Experiment with swirls, straight lines, waves and rough textures. You have time to experiment. Be inspired! Create an infinite variety of designs and finishes with different application and finishing tools. This is part of the designer fun - have with Liquid Surface Creations™, just as the name suggests.

At this stage Liquid Surface Creations must be applied on a flat and horizontal surface. A fter drying it can be installed in any position. For bathroom walls we suggest coating 6mm Villaboard™ and gluing the sheet with liquid nails over the existing tiles. Seal joints with coloured Fullers™ Polyurethane Sealant and hey presto – “a perfect finish!”. Future formulations may be suitable for application directly on horizontal walls and surfaces.

Cutting, Trimming, Installing & Sealing Splash Backs

When using Liquid Surface Creations™ for kitchen and bathroom splashbacks the coating must be applied on 6mm thick compressed cement board.

For example CSR Villaboard™ is recommended by the manufacturer for wet areas, kitchen splash backs and similar uses. For purely decorative purposes thinner board is acceptable and MDF, Plywood, chipboard, steel sheeting or any other flat surface may be preferable for weight or strength reasons. For Artworks and decorative paneling thinner MDF or ply wood is adequate.

At present Liquid Surface Creations™ applied on 6mm compressed cement sheet can be installed where the distance between the vertical surface and a gas burner is more than 200mm (refer Section on Fire Safety Below). Independent testing (CSIRO) is being undertaken regarding the installation of kitchen splashbacks closer than 200mm of a bench cook top. The product is totally non flammable and high temperature resistant and testing by Nutech Paint confirms this will be possible.

After the coating is cured the panel can be measured and trimmed to size using a simple 4 inch diamond blade on an angle grinder or circular saw. Placing strips of masking tape adjacent to the cut line will prevent accidental scratches or damage on new ‘green’ surfaces from saw or angle grinder guides and bases. Before or after installation the panels can be drilled to mark corners for power points and other switches then cut out’s removed easily with a small angle grinder.

Panels can be pre trimmed for exact sizing, and then post coated to ensure a perfect fit. Edges should be carefully trimmed with a sharp knife for a clean finish while the coating is still wet (e.g. within 1 hour). Dragging a knife along the edge may drag fresh coating, so care must be taken. After the coating is cured you can file or sand the edges for a very neat and clean finish. Take care when brushing dust off the surface of new boards. Compressed Cement Sheet contains sand and cement powder which is very abrasive if wiped over the fresh coating.

To install the product use Liquid nails or other suitable Polyurethane or Epoxy Adhesive on the rear of the sheet. Make sure an even film is applied. Press the sheet onto the backing and temporarily tape or brace onto the wall until the adhesive sets.

This splashback product can be installed over existing tiles and glass, cracked tiles and glass, plaster board, timber framing, ply wood, stone, steel or other similar structural surfaces.

Sealing edges and joints with bench tops with a clear silicon or coloured Polyurethane Sealant after installation is highly recommended (e.g. Fullers or Sika brand). This prevents water penetration behind the panel where damage may occur over time to the cement sheet or structure behind.

Floor Slip Hazard

Unlike a gloss ceramic tile, the polymer surface of Liquid Floor Art™ has a slight rubbery feel and most shoe soles grip very well to both wet and dry surfaces. At the HIA Home Show children were trying to slide on the glossy surface and were tripping up due to the unexpected grippy nature of the surface. With any smooth surface however wet feet on a wet surface can present a slip hazard. Spills of oily fluids or food can also create pedestrian safety hazard situations.

Adding extra texture to the finish when applying will provide additional texture and pedestrian grip.

As Liquid Surface Creations Pty Ltd will not be involved with the application or installation no responsibility can be accepted. Nutech Paint Anti Slip Additives are recommended for shower bases and other similar wet areas to guarantee pedestrian safety.

Cleaning & Maintenance

The surface is similar to a gloss polyurethane finish on a timber or stone surface. It can be scratched and marked if metal or stone objects are dragged across the surface.

Cleaning with a microfibre cloth, water and soap is recommended. Adding a small amount of Methylated spirits or other suitable mild non abrasive cleaner may be required occasionally to remove stubborn marks and before future recoating to strip the surface clean.

Application of a suitable liquid floor polish will extend and enhance the gloss surface, prevent damage and make cleaning easier. Refer to Nutech LSC Maintenance Guidelines for more detailed information.

Black shoe tread marks can be easily wiped off the surface using a dry or slightly wet micro fibre cloth mop.

If the Liquid Floor Art surface becomes scuffed the surface can be fully restored similar to a polished timber floor. Light sanding with wet and dry sandpaper and application of a new clear coat will restore the surface to a new appearance. Alternatively a ‘cut-n-polish’ treatment similar to the technique used for automotive coatings will restore the surface of LSC. On kitchen splashbacks and bench tops the wear characteristics will be very different to a floor and 10 to 20 years life expectancy is predicted provided harsh and abrasive cleaning products and scourers are avoided. It is possible to lightly sand, patch or even repair a vertical splashback and spray apply one clear coat to restore the surface at any time after installation.

On large floors wear characteristics are expected to exceed the performance of a timber floor if two coats of Nutech Aqua Polyurethane are applied over the LSC. On small high wear areas surfaces such as commercial counters will scuff quicker and some maintenance will be expected. However, unlike Melamine, Laminex™, PVC, stainless steel, stone or painted surfaces, Liquid Surface products can be restored to a new condition time and time again as required. Because the product is economical you could also apply a different colour over the top as fashion and colour schemes change to keep up with the times.

Product Safety & Handling

Liquid Surface products do not contain solvents, lead or other dangerous or toxic chemicals. Cleaning tools, spills and equipment may require the use of Nutech Epoxy Solvent (for fast action) or less hazardous Methylated Spirits (for slower reaction). These solvents are highly flammable and hazardous. Refer to specific Nutech Guidelines and Application Data for the correct and safe use of these products.

If you are coating a small splashback or floor you can throw away the trowel and stirrer after the coating dries. In this way you can keep the job totally solvent free.

Liquid Surface products contain chemical polymers (resins), special effect pigments and colourants which are not toxic in the liquid or solid form. With any chemical paint normal safety precautions should be taken to prevent skin and eye contact by wearing gloves and goggles and to prevent ingestion by persons or animals during application. Some people may become allergic to the liquid resin resulting in contact skin dermatitis with continual use. Infrequent or one off use of the product is highly unlikely to cause any problems provided contact is avoided with the liquid coating. If you are sensitive to chemicals we recommend that you do not use the liquid product and purchase the pre-fabricated sheet.

Wearing impervious gloves, eye goggles and long sleeve clothing during mixing and application will prevent skin and eye contact and reduce the requirement to use hazardous solvents for clean up. The dry coating is totally non-toxic and contains no dangerous products. Normal safety precautions should be taken when cutting, grinding, sanding or filing the dry product. Use of a dust mask and eye goggles is recommended during this process.

The product is a strong adhesive and will bond anything that becomes wet with the liquid coating. Clean up spills immediately with Methylated Spirits or Nutech Epoxy Thinners. These Thinners are highly flammable. Avoid Thinner contact with naked flames or ignition sources. Read “Safety Directions” on the containers before use. Refer to Liquid Surface Creations™ & Thinners Material Safety Data Sheets for additional safety and user information.

Kitchen Splashbacks, Bench Tops & Fire Safety

Where a kitchen splashback or bench is installed behind a gas or open flame cook top, special precautions are required to protect combustible surfaces including the bench top, wall and building structures underneath decorative surfaces.

Australian Standard AS 5601 - 2004 Gas Installations appli es to new installations, alterations and extensions commenced after the 4th November 2004. Under Clause 5.2.5 of the standard a ppliances (cook tops) must be installed in accordance with the Manufacturer’s instructions. These instructions normally specify the distance between the nearest burner to an adjacent vertical combustible surface (wall).

The Australian Standard AS 5601 - 2004 Gas Installations also states that protection is required under Clause 5.12.1.1 to ensure that the surface temperature of a combustible surface does not exceed 65 Degrees C. above the ambient temperature.

For example, a 200mm separation between the nearest burner and any combustible material is required where a toughened glass or stainless steel splashback is installed to comply with Clause 5.12.1.1. Glass and steel products conduct heat very well and surfaces behind them such as timber backing or framing could be heated to the point of combustion, unless suitable insulation or adequate separation distances are provided.

Liquid Surface Creations™ applied on a 6mm compressed cement board such as Villaboard™ is non combustible and it is not a good heat conductor. However, the surface that a Liquid Surface Creations splashback is glued to might be combustible for the purpose of the Australian Standard e.g., timber framing or plasterboard etc.

We are conducting independent testing to confirm that Liquid Surface Creations™ can be located closer than 200mm to the nearest gas burner. This testing should be completed shortly and results will be notified on our Web Site.

Colours & Effects

Initially only the liquid coating (Part A & Part B) will be available in a limited colour range;

Standard Colours, White ♣ & Metallic Effects*

Snow White ♣ Lilac Delight White/Green Glass

Silver Rocket Water Melon

Almond Chino Licorice Surprise

Deep Sea Blue Molten Pewter

Aqua Marine Golden Treasure*

Spearmint Fun Liquid Copper*

Special Colours

Later a full range of colours will be available by order.

The complete range of colours will include reds, greens, yellows, pinks, purples, oranges, blues, greys and black in infinite shades with special effect and colour enhancements pigment additives.

Subtle mother of pearls with pink, gold and yellow hues and luster’s are also available including the pure and very elegant Snow White. There is also a full range of molten glossy metallic effects including silver, aluminium, pewter, blue metal, copper, bronze, bright gold and antique gold. There is also a range of special colour change pigments and coloured and metallic glitters to further enhance to the range of possible visual effects.

Prices

Standard Colours 2 or 4 litres $50.00 per litre + GST

10 or 20 litres $45.00 per litre + GST

Snow White ♣ 2 or 4 litres $55.00 per litre + GST

10 or 20 litres $50.00 per litre + GST

Metallic Colours* 2 or 4 litres $60.00 per litre + GST

10 or 20 litres $55.00 per litre + GST

(P.O.A. for commercial quantities above 20 litres.)

Pre-Fabricated Cement Board

In future pre-coated 6.0 mm Villaboard™ (or equivalent) will be available from retailers in a range of standard colours and sizes including;

900mm x 1200mm 900mm x 2400mm 900mm x 3000mm

Larger sheet sizes of 1200mm x 3600mm & 1350mm x 4200mm may also be available as special orders.

Pricing for the pre-fabricated product is yet to be determined, although indications are that it will be less than one third of the price of installed glass.

Web Site

Our Liquid Surface Creations™ Web Site will be operating in the next few weeks which will contain availability, ordering, colour, pricing and testing updates.

www.liquidsurfacecreations.com.au

Information about Nutech Paint Pty Ltd is also available from the following Web Sites;

www.nutech.com.au

www.nutechpaints.com.au

www.flexishield

Orders & Suppliers

At this stage samples of the products are only available for inspection at;

Nutech Paint

4 Keppler Circuit

Seaford, Victoria.

Ph. 03 9770-3000

Fax.03 9770-1680

Email: sales@nutech.com.au

As manufacturing progresses samples will also be available for customers in Thomastown, Sydney, Brisbane, Perth, Tas, NZ and eventually through some Nutech wholesale outlets.

We hope to have coated samples of standard colours available for customers over the next months and we will keep you posted through the web site and direct mail.

We thought it would be appropriate to finish by quoting from some of the many hundreds of emails we have received from ABC viewers;

YOU SAID ………………

“How easy is this !”

“I was very impressed with your product on ABC Inventors”

“This new product enables the DIY person to create something unique by adding their own creative effects”

“What a snazzy appearance”.

“Liquid inspirations”.

“I believe your product will prove to be very popular”

“Your product is something I had wished existed but didn’t know it did. As I live in a rural area the cost of glass splashbacks is prohibitive, so this could be the answer.   I am excited about the many possible applications for my home, particularly if it is something that the lay person can use”

“I was told about your product by a friend that was very impressed”

“ What a fabulous product !”

“We saw your product last night and we were really impressed”

“Saw your product, looks wonderful !”

“Congratulations on such a great product”

“Guess you've been inundated after the show”

“Congratulations on your invention”

“Reckon it's a winner”

“Simple, economical, fantastic, where can we get it!”

“Watching the inventors last night I was gob smacked by your wonderful product”

“I missed the show last night but have plenty of people raving about it”

“I trust that you are enjoying being inundated with inquiries”

“I have been waiting for this. Good things come to those that wait…… and wait”

“Congratulations, a great product and looks fantastic and I am most interested”

“I think it is fantastic”

“Great to see such a wonderful invention that you created”

“I was watching the new inventors last night and was amazed at your product”

“Your system would be perfect, create an amazing finish and would be light weight”

“How can we get our hands on it? It would be a superb solution instead of having tiles”

“What a wonderful product you have here! I love that it enables a person to create something unique by adding their own creative effects”

“Congratulations on this fantastic looking product!”

“I was considering buying tiles for the splash-backs, however after seeing your product” “I’d actually like to try your product”

“Congratulations on a great product - it's just what we're after for our kitchen splashback”  

“I just had to write and say how fantastic I think your product is”

“I am in the process of finishing my kitchen, but don't want the expense of glass, your product looks perfect”

“Most impressed it looks wonderful”

Thank you for your overwhelming interest in this new product, we wish you all good luck with your renovation or building project!

Important Note

The information given in this information sheet is based on many years experience and is correct to the best of our knowledge. However since the use of our product, surface conditions, weather and a number of other factors are completely beyond our control, we can only be responsible for the quality of our product at the time of dispatch. For more information please contact our Company. As this information is of a general nature, we cannot assume any responsibility in individual cases.